Pm-1640tl 16x40? Ultra Precision Taiwan Heavy Duty Metal Lathe Free Shipping

  

Highest Quality Lathes, Made in TAIWAN. Spindle Bore clear through spindle for through- headstock work (Actual dimension 2.55? No change gears needed for the entire range of Inch and Metric thread pitches. Inch AND Metric thread cutting ability is a standard feature True INCH PITCH main lead screw, cross feed, and compound lead screws make it easy to use for the INCH measurement System, yet still has the Metric readings on dials for the ultimate in versatility for any job that may come about. Power feed on Carriage, and Cross Slide, both left and right, and in and out, for both turning and facing operations with automatic feed.

Allows for the best surface finish in all directions. Induction Hardened and Precision Ground Bed Ways to resist wear and give a long service life. Turcite B coating on carriage for extremely smooth operation and long life. All gears and shafts in headstock hardened and precision ground for long life, and precision ground for extremely quiet running. Meehanite Cast Iron used for rigidity and vibration dampening. Bed provides more stability in heavier work. Removable Gap for larger diameter work. High quality electronics used throughout machine.

Slip Clutch on feed rod, to help prevent overloading damage of feeds and allow the use of a solid micrometer carriage stop for repetitive work. High Precision Tapered Roller Bearings used in spindle, for the ultimate in long life, high precision, and best surface finishes. One shot lubrication pump on carriage for easier lubrication and longer life. Only Extremely High Precision Japanese Spindle Bearings are used. Locking Tang in tail stock is provided.

All Lathe Packages all come with. High Precision 9 3 Jaw Chuck, with Bolt On Jaws (can also use soft jaws). 2.55 (65mm) Spindle Bore.

Complete Cast Iron Base with slide out Chip Tray. High Precision (Japan) Spindle bearings, with +/.

Reducing Sleeve for Headstock Center. Feed Rod Clutch (To prevent overloading and using carriage stops). Everything Needed for listed Inch and Metric Thread Pitches. Coolant System (Single phase coolant pump, for those who want to run the machine with a VFD, no need to change out the pump). Headstock center to tailstock center 40?

Gap insert length 10 in. Spindle face to tailstock quill face 44? Compound (top slide) travel 4-15/16?

Spindle Mount D1-6 Camlock Quick Change. Internal taper of Spindle (With included reducing sleeve) MT 4. Spindle bore 2.55 in.

Diameter (will pass a 2.500? Low range, rpm 36, 50, 70, 105. Mid range 130, 180, 250, 380.

High range, rpm 620, 900, 1200, 1800. Carriage drive, thread cutting Leadscrew 4 TPI. Inch threads Choice of 45, from 2-72 TPI. Metric threads Choice of 39, from 0.2 mm to 14 mm pitch. Diametral Pitch (Worm Gear) Choice of 21, 8-44 DP.

Module Pitch (Worm Gear) Choice of 18. Longitudinal Feed rates from 0.002 to 0.067 in. Cross Slide Feed Rates from 0.001 to 0.034 in.

Spindle centerline to floor: 47 in. Weight, net, approximate: 3650 LBS add approx.

Power requirement 220 Vac, 60HZ, 3 Phase, 30 Amp Circuit. Motor TEFC type, 1725 rpm, 5HP (Single speed motor, not dual speed, great for VFD use).

If you would like to stop in and see one in person, we are at. 1060 Montour West Industrial Park. We are machinists here too, so we know what we sell.

This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. NO extra charge for residential or anything on these, as long as a truck can get to you, its covered.

If you have ANY questions, feel free to message us. Check out our other auctions for more lathes and mills.